The internet is one of the most used chunks of technology in today’s world. It is safe to say that all the technological advancements have been a reality only because of it. This develops a massive demand for a secure internet connection, especially at the offices. The router is a sustainable method to get your hands on high internet speed connectivity. It is connected with the modem cable and lets you transfer data from and to the online database. Hence, you can connect all the nearby devices to a single device as per requirement. One of the most used IP addresses for the office router is 192.168.1.99, and it can be found on several variants.
It is usual to forget the important credentials of the router and get locked out of it. There is nothing to panic about as this situation can be handled with a few steps. Today, we are going to discuss a strategy that can help to login to the router settings using admin credentials. This will allow you to make connection upgrades and boost internet speed. We will also include some of the default credentials for the 192.168.1.99 IP Address.
Router Using 192.168.1.99 As Default Getaway
Firstly, the 192.168.1.99 IP Address should be supported by the router on which you are working. Any stock IP for a given router is also called the Default Getaway and holds several functions. You can find the same details on the user guide or the backside of the device itself. Make sure that in case the IP address is something other than 192.168.1.99, try looking for another guide. Here is the list of a few router manufacturers that use the same IP address.
- Linksys WVC 200
- Fortinet FortiGate- 60C
- Also, Fortinet FortiWiFi- 60C
- Fortinet FortiGate- 50B
- Fortinet FortiGate- 60B
Still, there might be other manufactures using the same 192.168.1.99 IP Address with unknown sources. Try searching on Google regarding the default getaway of your router.
See also: Cisco Router Login – A Complete Guide
How To Login 192.168.1.99 IP Address?
It is a belief that someone doesn’t come across the 192.168.1.99 IP Address regularly. It is mainly required during setting the router for the first time. But there are chances that you need to login to the router using 192.168.1.99 IP Address.
One of them is the situation of managing the mainframe settings of the router. Eventually, you can analyze the data traffic and configure the device settings are per the requirement.
The following steps will show you the way to login into the router.
Click and open the browser installed on your desktop and fill in http://192.168.1.99 in the search bar.
Press Enter, and the login panel for 192.168.1.99 IP Address will appear on the front. Ensure that your device is already connected to the router.
Fill in the correct Username followed by the Password in their respective dialogue boxes.
Hit the Login option, and you will be directed to the final page that has all the setting options.
Know More: NETGEAR Router Firmware Update
Resetting The Router
Sometimes the login page might show an error due to the incorrect credentials. Try using the previously known username and passcode a couple of times, as it might be glitched. If the error persists, the credentials are not valid, or someone might have changed them in the past.
The best way to overcome this situation is by resetting the router. There is no rocket science in pulling this method and factory reset the device. This will remove all the parental changes, and your router will work like a new device. The steps to reset the router settings manually are list below.
Find the hard reset button on the back panel of the router. Don’t plug out the connection cord, and the router should be on during this process.
Find a thin needle or a pencil that can fit in the tiny hole of the button and press it.
You have to maintain the button pressed for at least 30 seconds for the reset to get successful.
There should be no downloads in progress on the connected devices as you will lose the internet. This is the safety measure of the router to reset its parental controls.
Note- Some of the users get confused between the two terms, “reset” and “reboot.” Resetting the router means that we are making changes at the level of the credential. All the changes made in the device will get reset to the factory defaults. On the other hand, rebooting the router refers to turning off the router for a few seconds. Turning it back will not hamper and the details like the Password or the Username. Moreover, this is mainly done to remove basic issues like the lag in connection. The above-mentioned steps were for ‘resetting’ the router.
Credentials After Factory Reset
It is important to note that all the changes will be removed after resetting the router. You will now have to log in using the default credentials set for the router. Many routers have them encrypted on the back panel or in the manual provided while purchasing. This will help you to get access to the router for the time being. You can change these details in the later stages. In order to save your time, we got some basic credentials for the 192.168.1.99 IP Address routers.
Format- “Username” and “Password”
“admin” and “admin.”
“user” and “user.”
“admin” and “password.”
“admin” and “(none)”
“user” and “password.”
The passcodes are case sensitive and make sure your CAPS LOCK is off while filling in the details.
All the steps mentioned in this guide will ensure a clean experience of high internet connectivity using the router. This was all about the major details of the 192.168.1.99 IP Address. If there are further issues, it is better to contact an expert to resolve the problem.
Seth Myers is a 26-year-old hardware expert who enjoys badminton, cycling and watching television. He is kind and fun, but can also be very hardworking and a bit lazy. In his free time he loves binge-watching boxed sets.